Bathtub Reglazing Cost in NYC

Bathtub reglazing in NYC starts at $435. Below is the full breakdown of what affects the price, plus our current promotional pricing.

Reglazing is the most affordable and time-saving way to update your fixtures. Avoid the high costs of demolition and inferior spray-on methods.

Replacing a tub often means hidden expenses:

New plumbing & fixtures

Tile and wall repairs

Professional removal fees

Refinishing typically costs about a third of what a full tub replacement runs.

Special Offer Until

SINK

Premium Pour-On Method
Ready in 24 hours
Odorless

Starting at: $385

$285

*tax included

GET A QUOTE

SHOWER

Premium Pour-On Method
Ready in 24 hours
Odorless

Starting at: $455

$355

*tax included

GET A QUOTE

BATHTUB

Premium Pour-On Method
Ready in 24 hours
Odorless

Starting at: $535

$435

*tax included

GET A QUOTE

Additional Services

SERVICE	COST
Caulking	Free with bathtub service
Distance surcharge	Travel fee for certain areas (e.g., Manhattan $25–$60).

GET A QUOTE

Why the Pour-On Method Wins — Every Time

CRITERIA	Traditional Spray-On Method	Pour-On Application (Our Method)
Typical lifespan	1-3 years	10-15 years
On-Site Work Time	~5 hours	3-4 hours
Coat thickness	6 mils	Several times thicker
Odor during work	Strong solvent smell, lingers	Mild, clears within hours
VOC content	High	Low
Safe to stay home	No — residents usually vacate	Yes
Ready to Use	~48 Hours	24 hours
Long-Term Value	Spray-on has a lower up-front cost, but the coating usually needs to be redone every couple of years.	A pour-on coat lasts long enough that most clients replace or sell the tub before the finish needs to be redone.

What Affects The Final Price

Most jobs fall close to the starting price. The factors that move the price up:

Tub size. Larger tubs need more material. Standard 5-foot tubs are at the starting price; oversized soaking tubs (6 feet and up) add to the cost.
Tub type and condition. Cast-iron and clawfoot tubs run higher than standard porcelain-on-steel — cast-iron needs more prep, clawfoot adds setup time because the tub is freestanding. The tub’s condition also affects the price: deep chips, rust spots, or a previous refinishing that’s peeling and needs to be stripped down to bare cast iron all take extra prep work.
Caulking and minor repairs. Caulking is free with bathtub service. Standard chip and crack repair is included in the base price; major structural repairs to the tub body are quoted separately.
Travel. Brooklyn jobs are at the standard rate. For Queens, the Bronx, Staten Island, and Manhattan, a travel fee of $25–$60 is added depending on the neighborhood. Manhattan tops out at $60 because of parking and access.

For a precise quote, send us a few photos of your tub — that’s the most accurate way to price the job in advance.

Frequently Asked Questions

How much does it cost to reglaze a bathtub?

Payment Bathtub reglazing starts at $435 for a standard tub. Cast-iron and clawfoot tubs run higher. Jobs outside Brooklyn include a travel fee of $25–$60 depending on the neighborhood. The fastest way to get an exact price is to send us a few photos through the form.

How is the work performed?

The work takes about three hours and follows three steps: prep, application, cure.

Prep. We sand down the existing enamel to a clean substrate, fill any chips, and clean the surface with a degreaser. Dust is contained with a vacuum-assisted sander, not blown around the apartment.
Application. The pour-on coating is mixed fresh by weight and poured along the tub rim. Gravity carries it down the walls and across the floor of the tub, where it self-levels into a smooth glossy finish. No spraying, no aerosols.
Cure. The drain stays taped off for 24 hours while the coating hardens. After that, the tub is ready for normal daily use.

What material is used?

An epoxy-based liquid polymer developed specifically for bathtub refinishing. It’s poured rather than sprayed, which lets it self-level into a thicker, more durable finish than spray-on coatings. The material is low-VOC and low-odor — there’s a mild smell during application that clears within an hour or two, and once cured it’s completely inert.

How long does the reglazing process take?

Time The entire process is quick and convenient, typically taking around 3 hours. More complex jobs might take up to 4 hours.

The material requires about 24 hours to fully dry and harden before you can use your “new” bathtub.

How long does the reglazed finish last?

With proper care, your professionally reglazed bathtub will look brilliant for 7 to 15 years.

10 to 15 years with normal care. The pour-on coat is several times thicker than a spray-on finish — typically 30–40 mils versus 6 mils — which is why it lasts so much longer. We back the work with a 5-year warranty.